elektronische bauelemente ES11M~es15m 50 ~ 600 v 1.0 amp surface mount efficient fast rectifiers 01-december-2008 rev. a page 1 of 2 rohs compliant product a suffix of ?-c? specifies halogen-free and rohs compliant descriptions z batch process design, excellent power dissipation offers better reverse leakage current and thermal resistance. z low profile surface mounted application in order to optimize board space. z small plastic smd package. z t rr less than 25ns for high efficiency z low forward drop down voltage z high surge and high current capability. z superfast recovery time for switching mode application. z glass-passivated chip junction. packaging information z case: molded plastic z epoxy: ul94-v0 rate flame retardant z weight: 0.0270 g (approximately) marking code part number marking code part number marking code es1 1 m e 1 es1 4 m e 4 es1 2 m e 2 es1 5 m e 5 es1 3 m e 3 electrical characteristics and ratings (t a = 25c unless otherwise specified.) part numbers parameters symbol ES11M es12m es13m es14m es15m units testing conditions recurrent peak reverse voltage (max.) v rrm 50 100 200 400 600 v rms voltage (max.) v rms 35 70 140 280 420 v reverse voltage (max.) v r 50 100 200 400 600 v forward voltage (max.) v f 0.875 1.25 1.75 v i f = 1a average forward rectified current (max.) i o 1.0 a ambient temperature = 55 c peak forward surge current i fsm 30 a 8.3ms single half sine-wave superimposed on rated load (jedec method) 5.0 v r =v rrm , t a =25 c dc reverse current at rated dc blocking voltage (max.) i r 100 a v r =v rrm , t a =125 c reverse recovery time t rr 2 5 ns junction capacitance (typ.) c j 15 pf f=1mhz and applied 4v dc reverse voltage storage and operating temperature range t stg , t j -65 ~ 175, -55 to 150 c sod-123m millimete r millimete r ref. min. max. ref. min. max. a 3.50 3.90 d 3.60 (max.) b 1.40 1.80 e 0.80 (typ.) c 1.30 1.70 f 0.30 (typ.) e e f b c d a
elektronische bauelemente ES11M~es15m 50 ~ 600 v 1.0 amp surface mount efficient fast rectifiers 01-december-2008 rev. a page 2 of 2 ratings and characteristic curves fig.1-typical forward characteristics fig.4-maximum non-repetitive forward surge current peak forward surge current,(a) fig.5-typical junction capacitance instantaneous forward current,(a) forward volt age,(v) 0 10 15 25 30 (+) (+) 25vdc (approx.) ( ) ( ) pulse generator (note 2) oscilliscope (note 1) 1 non- inductive w notes: 1. rise time= 7ns max., input impedance= 1 megohm.22pf. 2. rise time= 10ns max., source impedance= 50 ohms. +0.5a 0 -0.25a -1.0a | | | | | | | | 1cm set time base for 10 / 20ns / cm trr d.u.t. fig.3- test circuit diagram and reverse recovery time characteristics 10 noninductive 50 noninductive w w fig.2-typical forward current average forward current,(a) 0.2 0 0.4 0.6 0.8 1.0 1.2 derating curve reverse voltage,(v) junction capacitance,(pf) 40 30 25 20 15 10 5 0 .01 .05 .1 .5 1 5 10 50 100 number of cycles at 60hz 1 10 5 50 100 t =25 c j 8.3ms single half sine wave jedec method single phase half wave 60hz resistive or inductive load 0.375"(9.5mm) lead length ambient temperature ( c) 0 25 50 75 100 125 150 175 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.01 0.1 1 10 t j =25c pulse width =300 s 1% duty cycle ES11M ~ es13m es14m es15m 20
|
